SATO M-10E Spezifikationen PDF herunterladen (Seite 9)

M-10e Quick Guide Pg 9

Head Check Selection (DSW2-3) – When selected, the printer will check for head

elements that are electrically malfunctioning.

Hex Dump Selection (DSW2-4) – Selects Hex Dump mode.

Receive Buffer Selection (DSW2-5) – Selects the operating mode of the receive

buffer.

Firmware Download (DSW2-6) – Places the printer in the Firmware Download

mode for downloading new firmware into the flash ROM.

Protocol Code Selection (DSW2-7) – Selects the command codes used for protocol

control.

Status Select (DSW2-8) – For emulating earlier series software commands. Should

be used only if problems are encountered when using existing software. This switch

will also affect the settings selected by DSW1-7 and DSW1-8.

Backfeed Sequence (DSW3-1, DSW3-2) – Backfeed is used to correctly position the

label for application and then retract the next label to the proper print position. This

operation can be performed immediately after a label is printed and used, or

immediately prior to the printing of the next label.

Label Sensor Selection (DSW3-3) – Enables or disables the Label Sensor. If the

Sensor is enabled, it will detect the edge of the label and position it automatically. If

it is disabled, the positioning must be under software control using Line Feed

commands.

Back-Feed Selection (DSW3-4) – When Back-Feed is enabled, the printer will

position the last printed label for dispensing and retract it before printing the next

label. The amount of backfeed offset is adjustable.

EXT Print Start Signal Selection (DSW3-5) – Allows an external device to initiate a

label print for synchronisation with the applicator. When DSW3-5 is On, the unit is in

the Continuous print mode, Backfeed is disabled and External Signals are ignored.

External Signal Type Selection (DSW3-6, DSW3-7) – Both the polarity and signal

type (level or pulse) of the external print synchronising signal can be selected.

Repeat Print via External Signal (DSW3-8) – Allows the applicator to reprint the

current label in the print buffer.

M-10e Quick Guide Pg 6

Label Stock Loading

The M-10e has an automatic media loading feature, making it extremely easy to load.

1. Select the proper media sensing method

using the DIP switches on the Configuration

Panel. The printer comes from the factory

set up for label gap detection (DS2-2 and

DS3-3 both in the Off position). If Eye-

Mark labels are to be used, DS2-2 should be

placed in the On position.

2. Apply power to the printer.

3. Release the Print Head by pulling forward

on the Head Latch Lever.

4. Check to make sure that nothing is in the

media path. Remove any media that may

have been left in the printer.

5. Adjust the Label Width Guides by loosening

the thumbscrew and moving the guides in or

out to match the media width. The guides

are interlocked so that adjusting one will

automatically adjust the other side to

maintain a centre justified label path.

Tighten the thumbscrews.

6. Note that the Green Media Loaded LED on

the back panel is off.

7. Thread the media into the back of the printer

between the label guides. When it is

correctly positioned, the Green Media

Loaded LED will be on.

8. Close the Top Cover.

9. Place the printer Online by pressing the

LINE key.

10. The printer will automatically feed the media

into the printer until it is correctly positioned

for printing.

1 2 3 4 5 6 7 8 9 10

Kommentare zu diesen Handbüchern

Keine Kommentare

SATO M-10E Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Etikettendrucker SATO M-10E