SATO GL408e / GL412e Betreibershandbuch Seite 116
- Seite / 148
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Unit 4: Printer Configuration
GL408-412e Operator’s Manual
4-80
Select whether the data sent to the printer is translated as standard ASCII or EBCDIC. Many IBM
Mini/Main-Frame computers use EBCDIC which does not directly translate to ASCII.
• Disable - factory default. The IBM version of the selected character will not be used.
• Enable - the IBM version of the selected character set will be used.
This menu determines if a zero numeral character wil be printed with a diagonal slash overlayed.
• Font Based - factory default. Zero characters will print with a slash if the selected font type
designates that it has one. This mimics IPL3 printers where not all fonts contain a slashed
zero.
• Disable - factory default. Zero characters are never printed with a slash.
• Enable - all zero characters will be printed with a slash, independent of the selected font.
This menu defines the code page position that contains the the Euro symbol.
The factory default is 0x0.
Select whether the data is to be processed as it is received or if the printer is to wait until the
entire job has been sent prior to any commands being processed. This menu determines if the
data preparser will be active or inactive.
• Enable - factory default. The data received from the host is preprocessed to quickly respond
to the immediate commands.
• Disable - the data is processed synchronously; the commands are not processed until all
preceding commands have been processed.
This menu determines if a printer status message will be returned to the host on receipt of the
block terminator <ETX>. This is implemented only for serial interface, X-On/X-Off, or Intermec
protocol.
• Disable - factory default. Will not send status message.
• Enable - will send status message.
Cutter Command. This menu defines if the <ESC>SIc command which enables or disables the
cutter assembly is acknowledged.
• Process - factory default. Acknowledges cutter commands.
• Ignore - does not acknowledge cutter commands.
Power Up Mode Command. This menu defines if the <ESC>SIC command which selects the
Emulation or Advanced power up mode is acknowledged.
• Process - factory default. Acknowledges the commands.
• Ignore - does not acknowledge the commands.
End-Of-Print Distance Command. This menu defines if the <ESC>SID command is
acknowledged.
• Process - factory default. Acknowledges the commands.
• Ignore - does not acknowledge the commands.
Intensity Command. This menu defines if the <ESC>SId command which sets print darkness is
acknowledged.
• Process - factory default. Acknowledges the commands.
• Ignore - does not acknowledge the commands.
IGL EMULATION MODE (TABLE 4-14)
MENU DESCRIPTION
IBM Translation
Disable*
Slash Zero
Font Based*
EURO Symbol
0x0*
Preparsing data
Disable*
Status on <ETX>
Enable*
Cutter Cmd (c)
Process*
PwrUpMod Cmd (C)
Process*
EOP Dist Cmd (D)
Process*
Intens. Cmd (d)
Process*
- GL4xxe Operator’s Manual 1
- PN: 9001163B 2
- TABLE OF CONTENTS 3
- INTRODUCTION 6
- ABOUT THIS MANUAL 7
- GENERAL DESCRIPTION 8
- CONTROL FEATURES 9
- TECHNICAL DATA 10
- Unit 2: Technical Data 11
- GL408-412e Operator’s Manual 11
- REGULATORY 12
- CHARACTER FONT CAPABILITIES 13
- BARCODE CAPABILTIES 14
- INSTALLATION 15
- Accessory Box 16
- Shipping Container 16
- PRINTER INSTALLATION 17
- MEDIA SELECTION 18
- MEDIA & RIBBON LOADING 18
- Figure 3-3c, Ribbon Loading 19
- CONTINUOUS MODE 20
- TEAR-OFF MODE 20
- CUTTER MODE 20
- DISPENSE MODE 20
- LINERLESS MODE 20
- LABEL PRINT DIRECTION 21
- INTERFACE SELECTION 22
- READY/BUSY INTERFACE SIGNALS 23
- SIGNAL SIGNAL DEFINITION 23
- READY/BUSY CABLE REQUIREMENTS 23
- IEEE1284 PARALLEL INTERFACE 24
- 1 To Host 32 Fault To Host 24
- 1 From Host 24
- UNIVERSAL SERIAL BUS (USB) 25
- 802.11G WIRELESS 26
- WIRELESS LAN SIGNAL STRENGTH 27
- SOFTWARE SPECIFICATIONS 27
- ALL INTERFACES 28
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- EXTERNAL SIGNAL 31
- 25-PIN CONNECTOR ASSIGNMENTS 32
- INPUT SIGNAL WAVE FORM 33
- START PRINTING 33
- REPRINTING 33
- OUTPUT SIGNAL WAVE FORM 34
- BASIC OPERATION 34
- PAPER END 34
- RIBBON END 34
- MACHINE ERROR 34
- Unit 3: Installation 35
- ACCESSORIES INSTALLATION 36
- CONFIGURATION 37
- PRINTER CONFIGURATION 38
- CONFIGURATION MODES 39
- CONFIGURATION MODE 40
- ADVANCED MODE 41
- SERIAL INTERFACE MODE 43
- PARALLEL INTERFACE MODE 44
- CENTRONICS INTERFACE MODE 45
- PGL EMULATION MODE 49
- ZGL EMULATION MODE 50
- DGL EMULATION MODE 51
- TGL EMULATION MODE 52
- IGL EMULATION MODE 53
- DIAGNOSTICS MODE 54
- PRINTER MANAGEMENT MODE 55
- DISPLAY INTENSITY ADJUSTMENT 56
- BUFFER CLEAR 56
- SOFT RESET 57
- KEY LOCK/UNLOCK 57
- INTERFACES 58
- USER MODE (TABLE 4-1) 59
- ADVANCED MODE (TABLE 4-3) 65
- Data Protocol 78
- Buffer Size in K 78
- EMULATION 98
- MENU DESCRIPTION 100
- IGL Setup 118
- Save state* 118
- Priority Setting 118
- Command* 118
- Error Log Clear 120
- TROUBLESHOOTING 125
- ERROR SIGNAL TROUBLESHOOTING 126
- DISPLAY EXPLANATION SOLUTION 127
- TROUBLESHOOTING TABLE 132
- NO PRINTED IMAGE 133
- INCORRECT LABEL POSITIONING 133
- SMEARED PRINT IMAGES 133
- INTERFACE TROUBLESHOOTING 134
- LAN ETHERNET INTERFACE 135
- 802.11G WIRELESS INTERFACE 135
- CENTRONICS INTERFACE 135
- HEX DUMP 136
- TEST LABEL PRINTING 136
- Figure 6-2, Sample Test Label 137
- MAINTENANCE 138
- CLEANING PROCEDURES 139
- PRINT HEAD REPLACEMENT 140
- FUSE REPLACEMENT 141
- Platen Roller Assy 142
- Retaining Bracket 142
- Lower Print Assy 142
- LABEL SENSOR POSITIONING 143
- PRINT HEAD BALANCE ADJUSTMENT 144
- PRINT HEAD PRESSURE 145
- PRINT HEAD ALIGNMENT 146
- RIBBON GUIDE ALIGNMENT 147
- RIBBON ROLLER ALIGNMENT 148
Verwandte Produkte und Handbücher für Etikettendrucker SATO GL408e / GL412e
Etikettendrucker SATO LT408 Wartungshandbuch
(115 Seiten)
(115 Seiten)
Etikettendrucker SATO M8485S Betreibershandbuch
(228 Seiten)
(228 Seiten)
Etikettendrucker SATO M-84PRO Betreibershandbuch
(14 Seiten)
(14 Seiten)
Etikettendrucker SATO CG212DT Bedienerhandbuch
(109 Seiten)
(109 Seiten)
Etikettendrucker SATO M-5900 Wartungshandbuch
(66 Seiten)
(66 Seiten)
Etikettendrucker SATO /gt Series Wartungshandbuch
(106 Seiten)
(106 Seiten)
Etikettendrucker SATO CL608 Wartungshandbuch
(245 Seiten)
(245 Seiten)
Etikettendrucker SATO CG412 Spezifikationen
(100 Seiten)
(100 Seiten)
Etikettendrucker SATO CL608 Spezifikationen
(58 Seiten)
(58 Seiten)
Etikettendrucker SATO CT 412i Betreibershandbuch
(73 Seiten)
(73 Seiten)
Etikettendrucker SATO M-84PRO Spezifikationen
(52 Seiten)
(52 Seiten)
Etikettendrucker SATO CL408e Spezifikationen
(10 Seiten)
(10 Seiten)
Etikettendrucker SATO LM408e Spezifikationen
(86 Seiten)
(86 Seiten)
Etikettendrucker SATO LM408-LM412e Wartungshandbuch
(130 Seiten)
(130 Seiten)
Etikettendrucker SATO TH2 Bedienungsanleitung
(15 Seiten)
(15 Seiten)
Etikettendrucker SATO M-8400 Betreibershandbuch
(242 Seiten)
(242 Seiten)
Etikettendrucker SATO M8485S Betreibershandbuch
(107 Seiten)
(107 Seiten)
(87 Seiten)
Etikettendrucker SATO S8424 Standard Spezifikationen
(142 Seiten)
(142 Seiten)
Ce-niehoff-co N7390/A5-116 Replacement Instructions manuales
Manuales del propietario y guías del usuario para Hardware Ce-niehoff-co N7390/A5-116 Replacement Instructions.
Ofrecemos 1 manuales en pdf Ce-niehoff-co N7390/A5-116 Replacement Instructions para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern