SATO GL4XXE Wartungshandbuch Seite 168
- Seite / 204
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Unit 7: Replacement Procedures
GL4xxe Series Service Manual
7-29
INTERNAL REWINDER TIMING BELT REPLACEMENT
Before you can access the rewinder’s timing belt, remove all the necessary covers shown in “INTERNAL
REWINDER FRONT COVER REMOVAL” on page 7-25 and “INTERNAL REWINDER SIDE COVER REMOVAL”
on page 7-26.
1. Remove two binding screws labelled as item (1) in Figure 7-24
2. Remove the bracket (2) to access the timing belt (3).
3. Reverse the above procedures after replacing the belt.
Figure 7-24, Internal Rewinder Timing Belt Replacement
ldler pulleys
Rewinder Timing belt
- GL4xxe Service Manual 1
- O RADIO AND TV RECEPTION 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont’d) 4
- INTRODUCTION 7
- ABOUT THIS MANUAL 8
- GENERAL DESCRIPTION 9
- THEORY OF OPERATION 10
- CONTROL FEATURES 11
- Unit 1: Introduction 12
- GL4xxe Series Service Manual 12
- TECHNICAL DATA 13
- Unit 2: Technical Data 14
- REGULATORY 15
- CHARACTER FONT CAPABILITIES 16
- BARCODE CAPABILTIES 17
- INTERFACE 18
- SPECIFICATIONS 18
- INTERFACE SPECIFICATIONS 19
- SUPPORTED PROTOCOLS 20
- READY/BUSY INTERFACE SIGNALS 21
- IEEE1284 PARALLEL INTERFACE 22
- Table of IEEE1284 signals 23
- UNIVERSAL SERIAL BUS (USB) 25
- SOFTWARE SPECIFICATIONS 26
- 802.11G WIRELESS 27
- ALL INTERFACES 28
- RECEIVE BUFFER CONTROL 29
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- CHARTS AND DIAGRAMS 31
- PRINT SETUP DIMENSIONS 32
- LABEL PRINT DIRECTION 33
- LABEL ADJUSTMENT DIAGRAM 34
- READY/BUSY TIMING CHARTS 35
- X-ON/X-OFF TIMING CHARTS 36
- Unit 4: Charts And Diagrams 37
- CONFIGURATION 39
- PRINTER CONFIGURATION 40
- CONFIGURATION MODES 41
- CONFIGURATION MODE 42
- ADVANCED MODE 43
- SERIAL INTERFACE MODE 45
- PARALLEL INTERFACE MODE 46
- CENTRONICS INTERFACE MODE 47
- PGL EMULATION MODE 51
- ZGL EMULATION MODE 52
- DGL EMULATION MODE 53
- TGL EMULATION MODE 54
- IGL EMULATION MODE 55
- DIAGNOSTICS MODE 56
- PRINTER MANAGEMENT MODE 57
- MISC QUICK MENUS 58
- SOFT RESET 59
- KEY LOCK/UNLOCK 59
- MENU DEFINITION TABLES 60
- USER MODE (TABLE 4-1) 61
- ADVANCED MODE (TABLE 4-3) 67
- Data Protocol 80
- Buffer Size in K 80
- INTERFACES 90
- MENU DESCRIPTION 100
- EMULATION 101
- DIAGNOSTICS 120
- Priority Setting 120
- Command* 120
- IGL Setup 120
- Save state* 120
- Error Log Clear 122
- TROUBLESHOOTING 127
- ERROR TROUBLESHOOTING 128
- ERROR MESSAGES 129
- TROUBLESHOOTING TABLE 134
- NO PRINTED IMAGE 135
- INCORRECT LABEL POSITIONING 135
- SMEARED PRINT IMAGES 135
- INTERFACE TROUBLESHOOTING 136
- LAN ETHERNET INTERFACE 137
- 802.11G WIRELESS INTERFACE 137
- CENTRONICS INTERFACE 137
- TEST PRINT TROUBLESHOOTING 138
- Figure 6-2, Sample Test Label 139
- REPLACEMENT 140
- PROCEDURES 140
- REPLACEMENT PROCEDURES 141
- PLATEN ROLLER REPLACEMENT 142
- LABEL SENSOR REPLACEMENTS 143
- MAIN PCB REPLACEMENT 145
- POWER SUPPLY REPLACEMENT 147
- PCB during reassembly 148
- TIMING BELT REPLACEMENT 149
- RIBBON SENSOR REPLACEMENT 153
- HEAD-OPEN SENSOR REPLACEMENT 154
- RIBBON BOSS/TORQUE LIMITER 155
- Note the 156
- MEMORY CARTRIDGE REPLACEMENT 157
- INTERFACE BOARD REPLACEMENT 158
- CUTTER KIT REPLACEMENT 159
- REAL-TIME CLOCK REPLACEMENT 160
- Original front cover 162
- Figure 7-26, Replacement 170
- CHECKING / ADJUSTMENT 174
- PERFORMING TEST PRINTS 175
- RESETTING PRINT HEAD DATA 176
- SETTING THE LCD CONTRAST 178
- UPDATING THE PRINTER FIRMWARE 179
- HEAD OPEN SENSOR CHECKING 182
- PRINT DARKNESS ADJUSTMENT 183
- Pitch sensor holder 185
- I-Mark sensor position 185
- Gap Sensor position 185
- PRINT OFFSET ADJUSTMENT 186
- PRINT HEAD ALIGNMENT 187
- PRINT HEAD PRESSURE SETTING 188
- RIBBON TENSION ADJUSTMENT 190
- TIMING BELT ADJUSTMENTS 191
- SIMPLE DISPENSER ADJUSTMENT 193
- GLOSSARY 194
Verwandte Produkte und Handbücher für Drucken & Scannen SATO GL4XXE
Drucken & Scannen SATO LM408e Wartungshandbuch
(98 Seiten)
(98 Seiten)
Drucken & Scannen SATO CG4 Series Bedienerhandbuch
(102 Seiten)
(102 Seiten)
Drucken & Scannen SATO XL4xxe Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Drucken & Scannen SATO CL608 Spezifikationen
(12 Seiten)
(12 Seiten)
Drucken & Scannen SATO TH208 Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Drucken & Scannen SATO GY412 Bedienerhandbuch
(217 Seiten)
(217 Seiten)
Drucken & Scannen SATO XL400 Bedienungsanleitung
(194 Seiten)
(194 Seiten)
Drucken & Scannen SATO M8485Se Wartungshandbuch
(216 Seiten)
(216 Seiten)
Drucken & Scannen SATO CG412TT Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Drucken & Scannen SATO XL4xxe Bedienungsanleitung
(121 Seiten)
(121 Seiten)
(73 Seiten)
Drucken & Scannen SATO M8450 Bedienungsanleitung
(60 Seiten)
(60 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern