SATO GL4XXE Wartungshandbuch Seite 176
- Seite / 204
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Unit 8: Checking/Adjustment Procedures
GL4xxe Series Service Manual
8-3
RESETTING PRINT HEAD DATA
The print head stores a log of operation and performance history. To reset this data, perform the following proce-
dure. The procedure for a soft reset is detailed at the bottom of this page.
1. Press the LINE button until the printer is OFFLINE.
2. Press the FUNCTION button to display the various modes of the printer.
3. Use the cursor buttons to navigate to the Advanced Mode and press ENTER. If the screen shows the
word LOCKED at any time, you can unlock the ENTER button by pressing the down arrow and ENTER
button simultaneously.
4. Scroll to the Admin User option, and set it to ENABLE.
5. Press the FUNCTION button again to return to the main menu.
6. Use the cursor buttons to navigate to the Diagnostics Mode.
7. Scroll down to the Reset Head Data option and press ENTER. If prompted to proceed, press ENTER to reset
the following print head data: Print Head Usage and Head On Time.
Normal Soft Reset
This is performed by simply turning the printer OFF and then ON again, via the front
power switch.
Figure 8-3. Admin User menu
Figure 8-4. Admin User Enabled
Figure 8-5. Reset Head Data
Figure 8-6. Power Switc
- GL4xxe Service Manual 1
- O RADIO AND TV RECEPTION 2
- TABLE OF CONTENTS 3
- TABLE OF CONTENTS (cont’d) 4
- INTRODUCTION 7
- ABOUT THIS MANUAL 8
- GENERAL DESCRIPTION 9
- THEORY OF OPERATION 10
- CONTROL FEATURES 11
- Unit 1: Introduction 12
- GL4xxe Series Service Manual 12
- TECHNICAL DATA 13
- Unit 2: Technical Data 14
- REGULATORY 15
- CHARACTER FONT CAPABILITIES 16
- BARCODE CAPABILTIES 17
- INTERFACE 18
- SPECIFICATIONS 18
- INTERFACE SPECIFICATIONS 19
- SUPPORTED PROTOCOLS 20
- READY/BUSY INTERFACE SIGNALS 21
- IEEE1284 PARALLEL INTERFACE 22
- Table of IEEE1284 signals 23
- UNIVERSAL SERIAL BUS (USB) 25
- SOFTWARE SPECIFICATIONS 26
- 802.11G WIRELESS 27
- ALL INTERFACES 28
- RECEIVE BUFFER CONTROL 29
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- CHARTS AND DIAGRAMS 31
- PRINT SETUP DIMENSIONS 32
- LABEL PRINT DIRECTION 33
- LABEL ADJUSTMENT DIAGRAM 34
- READY/BUSY TIMING CHARTS 35
- X-ON/X-OFF TIMING CHARTS 36
- Unit 4: Charts And Diagrams 37
- CONFIGURATION 39
- PRINTER CONFIGURATION 40
- CONFIGURATION MODES 41
- CONFIGURATION MODE 42
- ADVANCED MODE 43
- SERIAL INTERFACE MODE 45
- PARALLEL INTERFACE MODE 46
- CENTRONICS INTERFACE MODE 47
- PGL EMULATION MODE 51
- ZGL EMULATION MODE 52
- DGL EMULATION MODE 53
- TGL EMULATION MODE 54
- IGL EMULATION MODE 55
- DIAGNOSTICS MODE 56
- PRINTER MANAGEMENT MODE 57
- MISC QUICK MENUS 58
- SOFT RESET 59
- KEY LOCK/UNLOCK 59
- MENU DEFINITION TABLES 60
- USER MODE (TABLE 4-1) 61
- ADVANCED MODE (TABLE 4-3) 67
- Data Protocol 80
- Buffer Size in K 80
- INTERFACES 90
- MENU DESCRIPTION 100
- EMULATION 101
- DIAGNOSTICS 120
- Priority Setting 120
- Command* 120
- IGL Setup 120
- Save state* 120
- Error Log Clear 122
- TROUBLESHOOTING 127
- ERROR TROUBLESHOOTING 128
- ERROR MESSAGES 129
- TROUBLESHOOTING TABLE 134
- NO PRINTED IMAGE 135
- INCORRECT LABEL POSITIONING 135
- SMEARED PRINT IMAGES 135
- INTERFACE TROUBLESHOOTING 136
- LAN ETHERNET INTERFACE 137
- 802.11G WIRELESS INTERFACE 137
- CENTRONICS INTERFACE 137
- TEST PRINT TROUBLESHOOTING 138
- Figure 6-2, Sample Test Label 139
- REPLACEMENT 140
- PROCEDURES 140
- REPLACEMENT PROCEDURES 141
- PLATEN ROLLER REPLACEMENT 142
- LABEL SENSOR REPLACEMENTS 143
- MAIN PCB REPLACEMENT 145
- POWER SUPPLY REPLACEMENT 147
- PCB during reassembly 148
- TIMING BELT REPLACEMENT 149
- RIBBON SENSOR REPLACEMENT 153
- HEAD-OPEN SENSOR REPLACEMENT 154
- RIBBON BOSS/TORQUE LIMITER 155
- Note the 156
- MEMORY CARTRIDGE REPLACEMENT 157
- INTERFACE BOARD REPLACEMENT 158
- CUTTER KIT REPLACEMENT 159
- REAL-TIME CLOCK REPLACEMENT 160
- Original front cover 162
- Figure 7-26, Replacement 170
- CHECKING / ADJUSTMENT 174
- PERFORMING TEST PRINTS 175
- RESETTING PRINT HEAD DATA 176
- SETTING THE LCD CONTRAST 178
- UPDATING THE PRINTER FIRMWARE 179
- HEAD OPEN SENSOR CHECKING 182
- PRINT DARKNESS ADJUSTMENT 183
- Pitch sensor holder 185
- I-Mark sensor position 185
- Gap Sensor position 185
- PRINT OFFSET ADJUSTMENT 186
- PRINT HEAD ALIGNMENT 187
- PRINT HEAD PRESSURE SETTING 188
- RIBBON TENSION ADJUSTMENT 190
- TIMING BELT ADJUSTMENTS 191
- SIMPLE DISPENSER ADJUSTMENT 193
- GLOSSARY 194
Verwandte Produkte und Handbücher für Drucken & Scannen SATO GL4XXE
Drucken & Scannen SATO LM408e Wartungshandbuch
(98 Seiten)
(98 Seiten)
Drucken & Scannen SATO CG4 Series Bedienerhandbuch
(102 Seiten)
(102 Seiten)
Drucken & Scannen SATO XL4xxe Bedienungsanleitung
(114 Seiten)
(114 Seiten)
Drucken & Scannen SATO CL608 Spezifikationen
(12 Seiten)
(12 Seiten)
Drucken & Scannen SATO TH208 Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Drucken & Scannen SATO GY412 Bedienerhandbuch
(217 Seiten)
(217 Seiten)
Drucken & Scannen SATO XL400 Bedienungsanleitung
(194 Seiten)
(194 Seiten)
Drucken & Scannen SATO M8485Se Wartungshandbuch
(216 Seiten)
(216 Seiten)
Drucken & Scannen SATO CG412TT Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Drucken & Scannen SATO XL4xxe Bedienungsanleitung
(121 Seiten)
(121 Seiten)
(73 Seiten)
Drucken & Scannen SATO M8450 Bedienungsanleitung
(60 Seiten)
(60 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern